The word “craft†means that workmanship is an art in itself. From the initial selection of raw materials for storage, to carpentry production, paint finishing and product packaging, not only the exquisite end products, but also the entire solid wood furniture production process. The art of flowing and flowing water is pleasing to the eye. Let Omido Furniture Xiaobian tell you today what the production process of solid wood furniture is .
Into the wood processing factory, it will be clear at a glance along the entire process flow in the production area.
One: stocking area
1. After the board is dried, the dried wood is not prone to burst deformation. The dried wood is naturally placed for several days to restore the balance of the wood.
2. The raw materials for the choice of ingredients, the wood products can be divided into three kinds according to their parts: external materials, internal materials and dark materials. Appearances exposed on the outside, such as the surface of the desk, the visible part of the cabinet, etc.; internal materials used inside the product, such as the internal file, the bottom plate, etc.; dark material refers to the parts that cannot be seen under normal use. , such as drawer guides, cladding panels, lining strips, etc. Pay attention to frugality, internal cracks, blue changes, dead wood, and cracks when selecting materials.
3. Rough shave trimming, setting the thickness of the wool sheet, trimming the length of the wool sheet, lengthening the length of the blank by 20 mm, cutting off the raw edges that cannot be used on the wool sheet.
4. With the board to make imposition, wood material matching plate selection rule grain, mountain pattern, the color matching is consistent, with the width of the board according to the required width of reasonable margin. When the materials are selected, the inner crack, the end crack, the thrift, the blue stain, and the dead wood must be removed, and the wood is assembled using a puzzle machine. The puzzles pay attention to the difference in height, length, color, and thrift.
5. After the glue is solidified, the wood is fixed by a single-saw, and the surface is planed. After the wood is shaved according to the required shape, the wood is naturally left for about 24 hours.
II: Woodworking Production Area
1. The wide sand is thick and thick, and the sand is processed to the required size according to the requirements. After the machine is finished, the sand is polished.
2. The length of the wool material is fixed. During the processing, no chipping or blackening occurs, and the wood is shaped according to the drawings. The surface of the machined part should be smooth, flat, and smooth.
3. Drill holes according to the process requirements of the drawings, drill holes for the products, and often test and check to ensure the quality of the products.
4. Assembled parts do not need to be disassembled, should be prepared before the preparation of the material, the process of grouping the glue coating evenly, set up a good semi-finished products, there should be no false nails, missing nail phenomenon, combined with strict, glue to wipe clean. After that, it was a large group and it was almost finished after assembly.
Three: coating area
1. Rubbing the color and the bottom coloring, wipe the color test is completed, according to the requirements of the swatch selection of the background color, the color difference between the material through the background color to adjust.
2. Primer and polish color, need to pass the primer three times, finish the primer, use 400# sandpaper to smooth and smooth the paint surface, paint surface is not allowed to have bright spots. Color correction also checks whether the product is a good product.
3. Finish the paint, clean the surface, and paint it. The entire process of finishing the paint is almost complete.
Four: Packaging
Inspection, blowing dust packaging, all in one.
Each producing area is perfectly coordinated, orderly, and amazingly manageable. It is the art of production. After reading your understanding of the solid wood furniture production process is how to understand it?
Quacent can turn any house design into a real house. However, we do encourage our clients to choose the SIPs optimized house plan which can save your cost and erection time. Please check with your sales rep to check if the house plan is suitable for Sips or not. You can choose from the ready-to-built house plan, or you can provide your customized house plan which reflects your more specific culture and preference. We can turn your dream into a real house.
Available Drummond House Plans
Available House Plans,Ready to Build Plans,SIPs House Plans,Cathedral Ceiling Roof
Dalian Quacent New Building Materials Co.,Ltd. , https://www.quacenthomes.com