Safety protective equipment use regulations

1 Hard hat
1. Everyone who enters the construction site must wear a safety helmet correctly.
2. The quality of helmets must comply with the national standards of GB2811-81. There are two certificate systems for factory certification and certification.
3. The use of safety helmets should be inspected frequently. Inspections and tests are carried out every year in accordance with the standards and there are damages, injuries, cracks, etc., and those that do not meet the requirements are resolutely scrapped.
2 seat belts
1. Select the appropriate seat belt according to the job.
2. When working at heights of 2 meters or more, you must wear a seat belt that meets the requirements.
3. The seatbelts meet the national standards of GB6095-85 before they can be used and checked regularly.
4. The various components on the seat belt shall not be arbitrarily removed or replaced, and a new sleeve shall be added when replacing the new one.
5. When high-altitude operations do not have the conditions for hanging seat belts, safety nets, safety ropes, and guard rails must be installed to ensure safety.
3 safety net
1. The safety net must be obtained by obtaining a permit from the local construction safety supervision and management department.
2. The specifications, materials, etc. of the safety net must comply with GB5125-1997 "Safety Net" and GB16909-1997 "Dense Eye Safety Net" national standards.
3. The dense mesh safety net must be completely closed outside the construction project.
4. The outer side of the material lifting frame body should use compact mesh and vertical net protection.
5. When the dense-mesh safety net is installed, each ring must be threaded into the compliant fiber rope or lead wire No. 12-14, firmly tied, the spacing between the fixed points should not be greater than 50CM, and the upper and lower meshes should be closely connected. .
6. To ensure that the safety net is evenly distributed, it is necessary to regularly clean up the web. There must be no accumulated material in the net.
7. The safety net is set up and can be used only after inspection and acceptance.
8. The dismantling of safety nets must be conducted under the close supervision of experienced personnel. The nets should be dismantled from top to bottom and fall prevention measures must be taken.
4 four protection
1. In the construction project's stairways, elevators, and exits, all reserved openings must be protected.
2. Staircase handrails should be installed in time after demolishing the stairs. Otherwise, except that 1.2, 0.6 should be set along the stairs
In addition to the meter body guardrails, a safety net should be fixed in the first floor of the well, and a safety net or scaffolding should be laid on every two floors.
3. In the elevator shaft under construction, a fixed safety net at the first floor shall be set in the well, a safety net or a scaffold shall be laid on every third floor, and the elevator shaft shall not be vertically transported. A 2-meter-high guard rail or movable door must be installed at each level of the elevator shaft to ensure it is solid and reliable.
4. A shelter must be erected at the entrance of the project under construction. The width of the shed should be greater than the entrance and exit, and its length should be set according to the height of the building.
5.500 * 500 mm below the hole, to be buried wire mesh or fixed cover. 500*500 mm 1500*1500 mm hole, to be buried long steel mesh, unconditional, can be fixed cover plate, more than 1 meter to leave the hole around the mouth should be set to a height of 0.6 meters, 1.2 meters double body protection body Railings, and depending on the depth of the hole set a fixed safety net. In addition to setting the cover plate at the four ports, there should be a prominent warning sign outside the fence, and an illuminated red light warning should be installed in the dark and at night.
5 Supervision edge protection
1. The construction project leading to the balcony door without a fence, the surrounding of the roof without a parapet, the periphery of the framework, the sides of the ramp, and the two sides of the unloading platform must have a double height of 1 meter. Fencing or support safety nets.
2. The construction of the construction of the top of the protective frame, is higher than the roof and provocation board 1.5 meters, higher than the flat roof surface of the daughter wall wall top 1 meter, the high part of the two security fences to be tied, and linked to the grid.
3. The project under construction is close to the street, houses and sidewalks. It is advisable that the protective roof be covered with wooden planks. The length and width of the protective roof shall ensure the safety of the buildings and houses.

This website solemnly declares: This article is the reprint of the online media, only represents the author's point of view, has nothing to do with this site. If news articles and comments infringe your legal rights, please call us and we will handle it in a timely manner.