The kitchen is finished, and you will find such a design regret when you use it after you check in. Now that the weather is getting warmer, our renovation army is slowly starting to prepare for work. At this time, Xiaobian specially arranged a few typical kitchen problems for everyone to explain. If you meet the same problem, I hope to Give you some lessons.
Regret 1: The refrigerator is in the kitchen, I want to have a horizontal line with the cabinet, at least not to protrude too much, but now...
Comments: When I started designing, I only thought about the location of the refrigerator, but I forgot to measure the width of the refrigerator. I could only endure it if I changed the refrigerator.
Regret 2: The interior partition of the kitchen cabinet is less, and the countertop is not on the board.
Regrets to tell: the door made by hand is not exquisite, the management of bargains is very chaotic, and many goods are not serious on the board. The interior partitions of the kitchen cabinets are less, and the countertops are not the same.
Comments: There are several layers of partitions inside the kitchen cabinet, yes.
Sorry 3: There is a deviation in the opening of the artificial stone countertop
Regrets: There is a deviation in the position of the artificial stone countertop opening, especially the undercounter basin. The workers with narrow countertops and large basins said that they could not install them.
Comments: From the opening position to the support plan, you must plan your own. Don't trust the wisdom of workers too much.
Regret 4: First install the cabinet and install the range hood to trouble
Regrets: After installing the cabinet, install the range hood, a big mistake!! The range hood is troublesome to install, and the seam between the cabinets is also relatively large. It is best to install at the same time.
Comments: The more such small things are easier to ignore, the owners measure the size before installation, and learn from others' experiences.
Sorry 5: The faucet is dirty when it is switched
Regret to say: the basin faucet must be well-handed with the back switch, the kind that must be kept clean with fingers, and it is difficult to turn when there is oil on the hand.
Comments: If you don't want to change the faucet, you can only work harder.
Regret 6: The edge band used on the cabinet is too expensive to buy. The edge banding used on the cabinet is best to buy more and compare more. If you buy other materials and buy it at the same time, it is impossible to get a good price. This is a very profitable product, very cheap!
Comments: shop around three since ancient times!
Regret 7: The keel spacing is relatively small. It will be very annoying to buy the sink later, the size will be limited. It is too expensive to go to the building materials supermarket, and the quality of the market is not good.
Comments: When considering the size of the sink in the kitchen cabinet, the keel spacing determines the size of the sink.
Regret 8: I don’t see it in the hood
Regrets: The home is an imported brand hood, which has a beautiful appearance and complete functions, but the smoking ability is too weak.
Comments: The flat body design is simple and stylish. However, it is not suitable for Chinese cooking, frying, cooking, and frying. Because the hood is too shallow or there is no hood at all, the fumes that are too late to escape are seriously spread. To solve this problem, it is recommended to change the deep-cover type range hood.
Regret 9: Unreasonable layout of the operation area, no position of the release board
The water pipe and the gas pipe are stacked together on the wall to save trouble, and the stove and the sink are installed close to the pipe. The distance between the sink and the side wall is less than 10 cm, and it is next to the cooktop, and there is almost no place for the board to operate. To make a dish, wash the vegetables on the right side of the stove, then cut the vegetables on the left side of the stove, and go back and forth, especially not easy.
Comments: The decoration kitchen must emphasize the practicality, not only the reasonable arrangement of the operation area in combination with the operation process, but also the height of the table, the height and thickness of the cabinet, the brightness of the light, etc., must be adjusted according to the specific needs of the owner. .
Sorry 10: use inferior hardware
Regrets: After less than a year of renovation, the cabinet door of the cabinet fell, and later I learned that the quality of the hardware was too bad, but regret it later.
Comments: The hardware on the cabinet can be said to be the most important part of the whole kitchen, even more important than the cabinet plate and countertop. It directly affects the overall quality of the cabinet, so the owner must be willing to spend money when customizing the cabinet. At the point.
[Scan the QR code below, pay attention to the WeChat public number "Jiuzheng cabinet network "; you can view the popular article " Cabinet: don't buy now, do you have to wait until the price increases?" 》 , want to communicate with peers can join the Jiuzheng building materials network cabinet exchange group]
Our aluminum alloy Emergency Restoration Tower has different structures. The LTQ110S type is designed with single-leg structure, while the rest types possess the portal-framed structure. Moreover, the 220kV portal-framed tower can also assemble the 110kV portal-framed type or 110kV single-leg type.
And our Aluminum Alloy Crossing Structure is fitted with the 04171 crossing structure backward installation lifter that needs to be purchased additionally.
Emergency Restoration Tower And Crossing Structure
Emergency Restoration Tower, Aluminum Alloy Crossing Structure
NINGBO MARSHINE POWER TECHNOLOGY CO., LTD. , https://www.marshine-power.com